Hatches leak for a variety of reasons, but mainly because of poor maintenance or failure to seal them properly after loading.

Coltraco Commitment To :

  • Through-life maintenance support
  • We still maintain units built 20 years ago
  • Extend trade-in credits - replace old units for new
  • UL listing & ABS type approval - Portalevel™ MAX
  • ABS type approval & RINA approval - Portascanner™
  • Be a life-safety technology partner – Permalevel™
  • Certified OEM calibration & ODA service stations

Coltraco manufacture Ultrasonics That Work

Hatches leak for a variety of reasons, but mainly because of poor maintenance or failure to seal them properly after loading.

 A watertight hatch cover is designed to prevent the passage of water in either direction under a head of water for which the surrounding structure is designed.  Many mariners may think hatches are robust, monolithic structures, thereby failing to appreciate the small tolerances on panel alignment and gasket compression. It is better to think of hatches as complex, finely-made structures, to be handled with care. All types of seals, experience dynamic stresses as part of their operational lifetime. For example, 4mm wear on the steel-to-steel contact is sufficient to damage rubber sealing gaskets beyond repair; 5mm sag along the cross-joint can cause a large gap between the compression bar and gasket.

The risk is worsened by the ageing nature of many bulk carrier ships in particular. There is also a degree of bending/deformation that naturally occurs in ships during travel, which puts pressure on hatch covers and can damage sealing. A recent wave of inexperienced crew members has swept across the shipping industry as a cost-saving mechanism, leaving vessel maintenance and hatch cover testing to decrease in quality. While hatch covers are often perceived as indestructible due to their large size and bulky exterior, in reality they are complex, finely made structures that need to be handled with care, a point that many mariners do not realise.

The case study of the Emma Maersk exemplifies the danger of improper servicing. A severe leakage occurred on the container ship in February 2013 when it was loaded with 14,000 containers. The leakage was caused because of a mechanical break-down of a stern thruster, creating the shaft tunnel to flood, as well as leading to severe ingress of water in the aft part. Eventually there was flooding of the main engine room. This was because of non-effective cable penetration sealings, in a sudden blast, four cable penetration sealings in the watertight bulkhead gave way to the water pressure followed by a massive ingress of seawater. Shortly after this, the other three cable penetration sealings also failed, resulting in an even larger ingress of water into the engine room. This led to approximately USD 45 million worth of damages and towage cost.

The use of UT is far more efficient than the traditional methods described in the previous section, taking less time and requiring no clean up while being in a portable, light-weight model for ease of use. Due to its convenience, UT tests can be conducted more frequently and can contribute to safety management and preventative maintenance procedures on board.

hatch covers testing

For further information, contact Coltraco Customer Service

 

CEO Message

Integrity and Science Key to Our Culture of Performance

Dear Coltraco Customers, Strategic Partners and Distributors,

Integrity is our defining value. Performance is its consequence. We understand that our customers have choices, and how we perform determines whether customers choose us. Coltraco’s Code of Ethics does not merely require compliance with laws. It embodies a Commitment to positive behaviours that build trust, promote respect, operate with distinction, with courtesy and global levels of performance, demonstrating our integrity and delivering customer performance.

We honour our commitments, communicate transparently, and act with honour. Ethics are the foundation of our performance culture and our science-based approach. We lead in specific technologies delivering the watertight integrity monitoring of marine structures and the monitoring of fixed liquefied gaseous fire extinguishing systems and the room integrity of protected space to ensure agent hold-times post-installation. We show this by our understanding of the science in them and the mathematics that explain them.

I would like to thank you for your business and for the relationships with our Customers, Strategic Partners, Distributors and ODAs who we value so highly.

My kindest regards,
Carl

Carl Stephen Patrick Hunter BA(Dunelm) Hon DSc FRINA FIMarEST MRAeS
CEO & Managing Director
Coltraco Ultrasonics Limited
46-47 Mount Street, Mayfair, London W1K 2SA
United Kingdom

Tel:  +44 20 7629 8475
Fax: +44 20 7629 8477

Call Now : +44 207 629 8475

 

References in PDF Format

 

Underwriters LaboratoriesUnderwriters Laboratories

 

Reference Alpha Fire UK Portalevel MAX Sept 2012

Reference Portascanner-II CSD MOD Albion and Bulwark

Quotation.

Quotation

Support.

Support

About Coltraco Ltd.

About

 
 

Request a Quotation

Online Submission

Click Here

Call: +44 207 629 8475
Our customer support line is open during UK
business hours
Mon-Friday, 9.00am - 5.00pm GMT

Email: sales@coltraco.co.uk
Enquire via email and a dedicated
member of the sales team will deal
with your request personally.

Cookies make it easier for us to provide you with our services. With the usage of our services you permit us to use cookies.